99精品国产一区二区三区不卡,天天摸天天做天天爽2020,最近中文字幕mv免费高清在线

Location: Homepage  > News center  > Industry news

[technical analysis] causes of high surface temperature of water cooled condenser

visits:41 addtime:2023-10-11 16:37:33

n the working process of the refrigeration system, the temperature of the outer surface of the water-cooled stage condenser should be close to the normal temperature, and the hands should not feel hot. Once the surface temperature is too high, the cause should be found out and measures should be taken to eliminate this phenomenon.


Generally speaking, the main cause of condenser temperature rise is the problem of cooling water. There are usually four kinds of feelings


Situation:


1) There is not enough cooling water and water pressure. The water-cooled condenser uses cooling water to take away the latent heat released during the condensation of refrigerant vapor. Therefore, the pressure of cooling water is not enough, the flow rate can not meet the rated requirements, and the heat dissipation capacity is limited, * which eventually causes the surface temperature of the condenser to rise.


2) The cooling water temperature is too high, which is higher than the rated operating temperature (usually 32 ℃). The cooling water temperature in Vietnam, the smaller the cooling temperature difference of refrigerant, the smaller the heat transfer, the refrigerant can not be effectively cooled, and the surface temperature of condenser will rise


High.


3) The poor quality of cooling water leads to scaling on the inner wall of the cooling water pipe in the condenser, increasing the thermal resistance, affecting the heat exchange between refrigerant and cooling water, and reducing the heat transfer effect. This kind of fault often occurs in the equipment which has been used for a long time and has not been cleaned regularly. The solution is to remove scale.


4) The inlet and outlet pipes of cooling water are installed incorrectly. The normal installation position is generally low inlet pipe position and high outlet pipe position


"Low in, high out.". If the inlet pipe is set high, the cooling water can not be completely filled in the condenser, the heat transfer area will be smaller, and the refrigerant vapor can not be effectively condensed, which will make the surface temperature of the condenser rise.


When the surface temperature of the condenser increases, it means that the condensation effect is recommended, and the cooling capacity of the system will decrease.


<menuitem id="uv949"></menuitem>
  • <menuitem id="uv949"><center id="uv949"><em id="uv949"></em></center></menuitem>
        主站蜘蛛池模板: 宁陵县| 永清县| 无码一区二区三区| 江孜县| 乐亭县| 国产又粗又猛又黄又爽无遮挡| 纳雍县| 4P被两个男人换着躁我小说| 天津市| 成人做爰A片免费看网站性晶| 欧美专区日韩视频人妻| 欧美av电影| 日本厕所间谍偷窥撒尿| 五指山市| 8拔插拔插X8免费视频X_拔插...| 成人影片麻豆国产影片免费观看 | 国产又粗又猛又黄又爽无遮挡 | 成人做爰A片免费播放魅影APP| 志丹县| 精品国产AV 无码一区二区三区| 3Dmax亚洲NINEBOXmod| 化州市| 日本无码一区| 怀仁县| 台北市| 青青青国产费线在线观看| 扶绥县| 被老师粗大jib捣出了白浆视频 | 四LLL少妇BBBB槡BBBB| 枝江市| 株洲市| 大竹县| 无棣县| 重庆市| 金昌市| 登封市| 嵊泗县| 交城县| 日韩av无码| 包头市| 娇乳欲女H奶汁翘|